Leave Your Message
100kW/215kWh All-in-One Liquid-Cooled Commercial & Industrial Energy Storage System
C&I Energy Storage & BESS

100kW/215kWh All-in-One Liquid-Cooled Commercial & Industrial Energy Storage System

Chudu Metal 100kW/215kWh All-in-One Liquid-Cooled C&I Battery Energy Storage System (BESS)

    1e678b7c-03d9-4928-8cbb-1ff079c6c4f3
    38738824-9022-4efd-bea0-ffef5a9f9086
    4d35f5de-bdef-47fa-8c1a-fcb4a6f32e05

    Product Overview


    Chudu Metal 100kW/215kWh All-in-One Liquid-Cooled C&I Battery Energy Storage System is designed for commercial and industrial energy storage applications, including factories, warehouses, industrial parks, commercial buildings, photovoltaic energy storage projects, EV charging stations and microgrids.

    The system combines a high-voltage Lithium Iron Phosphate (LiFePO4 / LFP) battery system, Battery Management System (BMS), Power Conversion System (PCS), power distribution, intelligent system control, liquid-cooled battery thermal management and multi-level safety protection in an integrated outdoor cabinet.

    With approximately 215kWh of battery energy capacity and 100kW of rated AC charge/discharge power, the system is suitable for peak shaving, load shifting, photovoltaic self-consumption, time-of-use energy management, demand management and backup applications where supported by the selected PCS and switching configuration.

    Current mainstream 100kW/215kWh C&I systems use this type of integrated high-voltage architecture.

    Main Features


    100kW / 215kWh Integrated C&I Energy Storage Architecture

    The system provides approximately:

    Rated AC Power: 100kW
    Battery Energy: 215kWh

    A typical all-in-one configuration can include:

    • LiFePO4 battery packs
    • Battery Management System (BMS)
    • Power Conversion System (PCS)
    • High-voltage DC protection
    • AC power distribution
    • Liquid cooling system
    • Fire detection and suppression system
    • Local system controller
    • EMS or EMS communication interface
    • Remote monitoring and communication

    The exact EMS architecture depends on the selected system configuration. Some current C&I systems integrate PCS, BMS and EMS, while others use an optional or system-level EMS controller.

    LiFePO4 Battery Technology

    The system adopts Lithium Iron Phosphate (LiFePO4 / LFP) battery chemistry.

    A representative configuration uses:

    Cell Voltage: 3.2V
    Cell Capacity: 280Ah
    Battery Configuration: 1P240S
    Nominal Energy: approximately 215kWh
    Nominal Battery Voltage: approximately 768VDC

    This 280Ah / 1P240S / 768V architecture is currently used in commercial 100kW/215kWh ESS products.

    High-Voltage Battery System

    The battery system operates on a high-voltage DC platform.

    A representative standard configuration provides:

    Nominal Voltage: 768VDC
    Operating Voltage Range: approximately 672–876VDC

    Actual operating voltage range may vary according to battery cell limits, BMS settings and PCS configuration.

    For example, current 215kWh products specify ranges including 672–876VDC, 649–876VDC and 660–864VDC.

    Integrated 100kW PCS

    The integrated bidirectional Power Conversion System (PCS) manages AC/DC power conversion between the battery system and the utility/load side.

    Typical functions include:

    • Battery charging
    • Battery discharging
    • AC-to-DC conversion
    • DC-to-AC conversion
    • Grid-connected operation
    • Active and reactive power control
    • Power-factor control
    • Energy dispatch according to EMS commands

    Off-grid or backup operation requires a PCS with grid-forming capability and suitable transfer/switching equipment and should not be assumed for every configuration.

    Liquid-Cooled Battery Thermal Management

    The battery side uses intelligent liquid cooling to maintain suitable cell operating temperatures and improve temperature uniformity across battery packs.

    The liquid-cooling system can include:

    • Liquid cooling plates
    • Coolant circulation loop
    • Pump
    • Heat exchanger / chiller
    • Temperature sensors
    • Thermal management controller

    Current liquid-cooled C&I systems use this architecture to reduce battery-cell temperature differences and improve thermal consistency.

    Note: The battery system is liquid-cooled. The PCS may use independent smart air cooling depending on system design.

    Battery Management System

    The integrated Battery Management System (BMS) can monitor and manage:

    • Cell voltage
    • Battery pack voltage
    • Total battery voltage
    • Charge current
    • Discharge current
    • Cell temperature
    • State of Charge (SoC)
    • State of Health (SoH), where supported
    • Cell balancing
    • Insulation status
    • Alarm status
    • Battery protection status

    Typical protection functions include:

    • Overvoltage protection
    • Undervoltage protection
    • Overcurrent protection
    • Short-circuit protection
    • Over-temperature protection
    • Low-temperature protection
    • Insulation fault protection
    • Communication fault protection

    Energy Management

    Depending on the selected configuration, EMS functions may be integrated into the cabinet or provided by an external/system-level controller.

    Typical functions include:

    • Peak shaving
    • Load shifting
    • Time-of-use optimization
    • PV self-consumption
    • Demand management
    • Charge/discharge scheduling
    • Remote monitoring
    • Multi-cabinet coordination
    • Energy statistics
    • Alarm and operating-data management

    High Depth of Discharge


      Selected systems support:

      Up to approximately 95% Depth of Discharge (DoD)

      Final DoD depends on cell chemistry, BMS strategy and warranty conditions. Current 100kW/215kWh 280Ah systems are available with up to 95% DoD.

      Modular Expansion


      Multiple 100kW/215kWh cabinets can be connected to create larger systems.

      Typical nominal configurations include:

      Cabinet Quantity

      System Power

      Nominal Energy

      1

      100kW

      215kWh

      2

      200kW

      430kWh

      3

      300kW

      645kWh

      4

      400kW

      860kWh

      5

      500kW

      1.075MWh

      Current modular C&I systems use this same cabinet-expansion concept.

      Technical Specifications


      Parameter

      Specification

      Product Type

      All-in-One Liquid-Cooled C&I Battery Energy Storage System

      Rated AC Power

      100kW

      Nominal Battery Energy

      Approx. 215kWh

      Battery Chemistry

      Lithium Iron Phosphate (LiFePO4 / LFP)

      Typical Cell Specification

      3.2V / 280Ah

      Typical Battery Configuration

      1P240S

      Nominal Battery Voltage

      Approx. 768VDC

      Battery Operating Voltage

      Approx. 672 – 876VDC, Reference Configuration

      Charge / Discharge Rate

      Typically ≤0.5C

      Recommended Depth of Discharge

      Up to Approx. 95%, Model Dependent

      Rated Grid Voltage

      380VAC / 400VAC, Market and Model Dependent

      Rated Grid Frequency

      50Hz / 60Hz

      Grid Connection

      Three-Phase; 3L+N+PE on Applicable Models

      AC Current THD

      Typically ≤3% at Rated Operation on Applicable Models

      System Round-Trip Efficiency

      Typically Approx. 88% – 90%+, System Dependent

      Battery Management System

      Integrated BMS

      Power Conversion System

      Integrated Bidirectional PCS

      Energy Management

      Integrated or System-Level EMS, Depending on Configuration

      Battery Thermal Management

      Intelligent Liquid Cooling

      PCS Cooling

      Air Cooling / Model Dependent

      Fire Detection

      Temperature / Smoke / Other Sensors, Configuration Dependent

      Fire Suppression

      Aerosol / Gas / Water-Based System, Configuration Dependent

      Enclosure Protection

      Typically IP54 / IP55

      Operating Temperature

      Typically Approx. -20°C to 55°C

      Temperature Derating

      Typically Above Approx. 45°C

      Operating Humidity

      Typically 0 – 95% RH, Non-Condensing

      Installation Altitude

      Typically Up to Approx. 3000m; Higher Altitude Available on Selected Models with Derating

      Communication

      Ethernet; 4G / RS485 / Other Interfaces on Selected Models

      Cycle Life

      ≥6,000 Cycles on Applicable Models under Specified Conditions

      Installation

      Outdoor Floor-Mounted Cabinet

      Expansion

      Multi-Cabinet Parallel Operation Supported

      Application

      Commercial & Industrial Energy Storage

      The principal reference values above are consistent with current 100kW/215kWh systems from Deye, Sungrow and Billion; enclosure, RTE, communication and environmental limits vary by model.

      Note: Final voltage range, dimensions, weight, cycle life, communication interfaces, fire-protection configuration, enclosure rating and certification package shall be confirmed according to the selected production model.

      Reference Battery Parameters


      Parameter

      Reference Specification

      Battery Chemistry

      LiFePO4 / LFP

      Cell Specification

      3.2V / 280Ah

      System Configuration

      1P240S

      Nominal Energy

      Approx. 215.04kWh

      Nominal Voltage

      Approx. 768VDC

      Operating Voltage

      Approx. 672 – 876VDC

      Charge / Discharge Rate

      ≤0.5C

      DoD

      Up to Approx. 95%

      Thermal Management

      Liquid Cooling

      The 215.04kWh nominal value results from the representative 3.2V × 280Ah × 240-cell series configuration used by current systems.

      Reference AC Parameters

      Parameter

      Reference Specification

      Rated AC Power

      100kW

      Rated Grid Voltage

      380VAC / 400VAC

      Rated Frequency

      50Hz / 60Hz

      Grid Type

      Three-Phase

      Wiring

      3L+N+PE on Applicable Models

      THDi

      Typically ≤3% at Rated Power on Applicable Models

      Current products use both 380V and 400V three-phase configurations depending on market.

      4d35f5de-bdef-47fa-8c1a-fcb4a6

      Working Principle


      The system can store electrical energy from a photovoltaic system or the utility grid.

      When solar generation exceeds site consumption, or when electricity prices are low, the battery can be charged through the integrated PCS.

      When electricity demand increases or electricity prices are higher, stored battery energy can be converted by the PCS and supplied to commercial or industrial loads.

      The EMS or system controller can manage battery charging and discharging according to:

      • PV generation
      • Site load
      • Battery State of Charge
      • Electricity tariffs
      • Demand limits
      • User-defined energy strategies
      • Grid conditions

      Typical Operating Modes


      PV Self-Consumption

      Excess photovoltaic energy is stored in the battery for later use, increasing onsite utilization of solar energy.

      Peak Shaving

      The battery discharges when facility demand approaches a preset limit, helping reduce peak grid demand.

      Time-of-Use Energy Management

      The battery can charge during lower-price periods and discharge during higher-price periods according to electricity tariff settings.

      Load Shifting

      Electrical energy can be moved from periods of lower demand or lower electricity cost to periods of higher demand.

      Backup Power

      Backup power operation can be supported when the selected system includes appropriate grid-forming PCS functionality, protection and transfer equipment.

      Microgrid Operation

      Compatible systems can be integrated with:

      Solar PV + Utility Grid + Energy Storage + Generator + Loads

      according to project requirements.

      Applications


      The system is suitable for:

      • Manufacturing plants
      • Factories
      • Warehouses
      • Industrial parks
      • Commercial buildings
      • Shopping centers
      • Office buildings
      • Hotels
      • Agricultural facilities
      • Logistics centers
      • EV charging stations
      • PV + Energy Storage projects
      • Microgrids
      • Peak-shaving projects
      • Demand-management projects
      • Backup power applications

      Typical C&I Energy Storage System


      A typical installation can include:

      **Solar PV Modules

      • PV Inverter
        + 100kW/215kWh All-in-One C&I ESS
      • EMS / System Controller
      • Smart Meter / CT
      • Utility Grid
      • AC Distribution
      • Commercial or Industrial Loads**

      For backup applications, an STS or other approved transfer device may be required depending on system architecture.

      All-in-One C&I ESS vs. High-Voltage Battery Cabinet


      High-Voltage Battery Cabinet

      A standalone high-voltage battery cabinet mainly contains:

      • Battery cells and packs
      • BMS
      • DC protection
      • Battery thermal management
      • Fire protection
      • Communication equipment

      It generally requires an external PCS for AC/DC conversion.

      All-in-One C&I BESS

      An all-in-one C&I energy storage system integrates more system-level equipment, typically including:

      • Battery system
      • BMS
      • PCS
      • Power distribution
      • Liquid cooling
      • Fire detection and suppression
      • System control
      • EMS or EMS interface

      This reduces onsite integration work compared with a standalone DC battery cabinet.

      Safety & Protection


      Depending on configuration, protection functions may include:

      • Cell overvoltage protection
      • Cell undervoltage protection
      • Battery overcurrent protection
      • Short-circuit protection
      • Over-temperature protection
      • Low-temperature protection
      • Insulation monitoring
      • Smoke detection
      • Temperature detection
      • Pressure monitoring
      • Fire suppression
      • Audible and visual alarm
      • Emergency stop
      • AC-side protection
      • DC-side protection
      • Communication fault protection

      Fire Detection & Suppression


      Depending on model and destination-market requirements, the system can use combinations of:

      • Smoke detection
      • Temperature detection
      • Pressure monitoring
      • Aerosol fire suppression
      • Gas-based suppression
      • Water-based fire protection
      • Audible and visual alarm
      • Emergency shutdown

      Sungrow and Billian's current systems demonstrate multi-sensor detection and system-level fire suppression architectures, but the exact method differs between products.

      Monitoring & Communication


      Depending on system configuration, monitoring parameters can include:

      • State of Charge
      • State of Health
      • Cell voltage
      • Battery voltage
      • Battery current
      • Charge/discharge power
      • Cell temperature
      • Battery thermal-management status
      • PCS operating status
      • Grid voltage
      • Grid frequency
      • Alarm information
      • Fire-protection status
      • Energy throughput
      • Historical operating data

      Typical communication options include:

      Ethernet / Modbus TCP / RS485 / 4G

      depending on the selected controller and system configuration.

      Environmental Requirements


      Typical outdoor operating conditions include:

      Operating Temperature: approximately -20°C to 55°C
      Operating Humidity: approximately 0–95% RH, non-condensing
      Protection Rating: typically IP54 / IP55
      Installation: outdoor floor-mounted
      Maximum Altitude: typically approximately 3000m, with selected systems supporting higher altitude subject to derating

      Representative products currently range from IP54 to IP55 and approximately 3000–4000m maximum installation altitude.

      Compliance, Safety & Transport Documentation


      Depending on the selected model and destination market, applicable standards and documents may include:

      • IEC 62619
      • IEC / EN 62477-1
      • IEC 61000 series
      • CE requirements, where applicable
      • UL 1973, where applicable
      • UL 9540A test documentation, where applicable
      • UN38.3
      • SDS
      • Local grid-connection requirements

      Current mainstream systems reference IEC 62619 for battery safety, IEC 62477 for power-conversion equipment, IEC 61000 EMC requirements and UN38.3 for lithium-battery transport.

      UN38.3 is lithium-battery transport testing/documentation. SDS is safety documentation. UL 9540A is a thermal-runaway fire-propagation test method and should not be presented simply as a universal product certification.

      Information Required for Quotation


      For accurate system selection and quotation, please provide:

      1. Required energy storage capacity
      2. Required charge/discharge power
      3. Daily electricity consumption
      4. Maximum site load
      5. Existing or planned solar PV capacity
      6. Local grid voltage and frequency
      7. Peak and off-peak electricity tariff periods
      8. Required backup duration
      9. Whether backup or off-grid operation is required
      10. Whether generator integration is required
      11. Required number of ESS cabinets
      12. Installation environment
      13. Ambient temperature range
      14. Installation altitude
      15. Destination country
      16. Required certifications
      17. Local grid-connection requirements
      18. Fire-protection requirements

      Packing & Shipping


      The 100kW/215kWh C&I BESS is heavy lithium-battery equipment and requires professional export and transportation planning.

      Depending on the final configuration and destination, applicable documents may include:

      • UN38.3 test documentation
      • SDS
      • Dangerous Goods Declaration
      • Lithium battery transport documentation
      • Other destination-specific shipping documents

      Forklift handling, lifting requirements, reinforced export packaging, container loading and destination unloading arrangements should be confirmed before shipment.

      Chudu Metal

      Solar PV Modules, Solar Mounting Components & Solar Product Supplier from China
      🌐 Website:  www.chudufastener.com
      📧 Email:  han@hbchudu.com
      📱 WhatsApp / Phone: +86 19333039217

      description2

      Contact Us

      Our experts will solve them in no time.